Search Results

The durability peak load events Driving over a curb and Skid against a curb have been simulated in Adams for a Volvo S80. Simulated responses in the front wheel suspension have been validated by comparison with measurements. Due to the extreme nature of the peak load events, the component modeling is absolutely critical for the accuracy of the simulations. All components have to be described within their full range of excitation. Key components and behaviors to model have been identified as tire with wheel strike-through, contacts between curb and tire and between curb and rim, flexibility of structural components, bump stops, bushings, shock absorbers, and camber stiffness of the suspension. Highly non-linear component responses are captured in Adams. However, since Adams only allows linear material response for flexible bodies, the proposed methods to simulate impact loads are only valid up to small, plastic strains.

The development of a new combustion system for a light-duty diesel engine is presented. The soot-NOx trade-off is significantly improved with maintained or improved efficiency. This is accomplished only by altering the combustion chamber geometry, and thereby the in-cylinder flow. The bowl geometry is developed in CFD and validated in single cylinder tests. Tests and simulations align remarkably well. Under identical conditions in the engine the new combustion chamber decreases smoke by 11-27%, NOx by 2-11%, and maintains efficiency as compared to the baseline geometry. The injector nozzle is matched to the new bowl using design of experiments (DoE). By this method transfer functions are obtained that can be used to optimize the system using analytical tools. The emissions show a complex dependence on the nozzle geometry. The emission dependence on nozzle geometry varies greatly over the engine operating range.

During the development of the aerodynamic properties of fore coming road vehicles down scaled models are often used in the initial phase. However, if scale models are to be utilised even further in the aerodynamic development they have to include geometrical representatives of most of the components found in the real vehicle. As the cooling package is one of the biggest single generators of aerodynamic drag the heat exchangers are essential to include in a wind tunnel model. However, due mainly to limitations in manufacturing techniques it is complicated to make a down scaled heat exchanger and instead functional dummy heat exchangers have to be developed for scaled wind tunnel models. In this work a Computational Fluid Dynamics (CFD) code has been used to show that it is important that the simplified heat exchanger model has to be of comparable size to that of the full scale unit.

This paper presents how hardware in the loop (HIL) simulations have been used for testing during the development of the adaptive cruise control (ACC) and collision warning with brake support (CWBS) functions implemented in the Volvo S80. Both the brake system controller and the controller where the ACC and CWBS functions were implemented were tested. The HIL simulator was used for automated batch simulations in which different controller software releases were analyzed from both system, fail-safe and functional performance perspectives. This paper presents the challenges and the benefits of using HIL simulations when developing distributed active safety functions. Some specific simulation results are analyzed and discussed. The conclusion shows that although it is difficult and time-consuming to develop a complete HIL simulation environment for active safety functions such as ACC and CWBS, the benefits justify the investment.

The low frequency acoustic response of the passenger compartment (cavity) in sedans is considered with respect to the coupling between the cavity and the trunk. Both acoustic (via holes in the parcel shelf or behind the backrest of the rear seat), and structural (via the parcel shelf itself, or the panel of the backrest) mechanisms are investigated by both test and CAE. It is found that the peaks in acoustic response of the cavity at low frequencies are due to both acoustic and structural phenomena. However, the acoustic ones can be effectively blocked by proper design of the trim. Recommendations concerning modeling of acoustic effects in sedans are formulated.

It has been shown that Inflatable Curtains have the potential to reduce head injuries in side impacts and the system has accordingly been introduced on a growing number of car models. There is also a potential benefit in rollover situations. This paper only consider performance in situations with belted occupants. To date, it has not been possible to implement an Inflatable Curtain in convertible vehicles because they lack a roof. The challenge of the Door Mounted Inflatable Curtain (DMIC) has been to overcome the lack of support and fixation possibilities offered by a roof. This paper includes a description of the DMIC and how it was integrated into the vehicle structure. The paper will also show how to create the space and support needed to utilize the internal stiffness and make it possible to fill the bag in time. The impact attenuation and ejection protection functions of the DMIC will be demonstrated.

One way of avoiding crashes or mitigating the consequences of a crash is to apply an autonomous braking system. Quantifying the benefit of such a system in terms of injury reduction is a challenge. At the same time it is a fundamental input into the vehicle development process. This paper describes a method to estimate the effectiveness of reducing speed prior to impact. A holistic view of quantifying the benefit is presented, based on existing real life crash data and basic dynamic theories. It involves a systematic and new way of examining accident data in order to extract information concerning pre-crash situations. One problem area when implementing collision mitigation systems is being able to achieve sufficient target discrimination. The results from the case study highlight frontal impact situations from real world accident data that have the greatest potential in terms of improving accident outcome.

The objective of this paper is to investigate whether different appearance modes of the digital human models (DHM or manikins) affect the observers when judging a working posture. A case where the manikin is manually assembling a battery in the boot with help of a lifting device is used in the experiment. 16 different pictures were created and presented for the subjects. All pictures have the same background, but include a unique posture and manikin appearance combination. Four postures and four manikin appearances were used. The subjects were asked to rank the pictures after ergonomic assessment based on posture of the manikin. Subjects taking part in the study were either manufacturing engineering managers, simulation engineers or ergonomists. Results show that the different appearance modes affect the ergonomic judgment. A more realistic looking manikin is rated higher than the very same posture visualized with a less natural appearance.

This paper describes how simultaneous numerical simulation of cooling performance and aerodynamic drag can be used to achieve attribute-balanced solutions. Traditionally at Volvo, evaluation of cooling performance and aerodynamics are done by separate teams using separate models and software. However, using this approach, any project changes can be evaluated in terms of their effect on cooling performance and drag from one single model. This enables the project to make decisions that are optimal in a more global perspective. If several proposals have similar levels of cooling performance, the proposal that yields the lowest overall drag can be chosen, thus reducing the fuel consumption of the vehicle. The first part of the paper discusses the prerequisites for the method in terms of boundary conditions, mesh and solution strategy. For the cooling performance part, the importance of high quality boundary conditions is reviewed.

This paper describes the development of a robust and accurate method to model one-phase heat exchangers in complete vehicle air flow simulations along with a comprehensive comparison of EFD and CFD results. The comparison shows that the inlet radiator coolant temperatures obtained with CFD were within ±4°C of the experimental data with a trend in the differences being dependent on the car speed. The relative differences in cooling air mass flow rates increase with increasing car speed, with CFD values generally higher than EFD. From the investigation, the conclusion is that the methodology and modeling technique presented offer an accurate tool for concept and system solutions on the front end design, cooling package and fan. Care must be taken in order to provide the best possible boundary conditions paying particular attention to the heat losses in the engine, performance data for the radiator and fan characteristics.

When developing gas exchange and combustion systems at Volvo Car Corporation, CFD (Computational Fluid Dynamics) is today a key tool. Three dimensional CFD is by tradition used to study one single component (e.g. manifolds and ports) at a time. Our experience is that this approach suffers from two main limitations; first that the boundary conditions (both upstream and downstream) are uncertain; and secondly that validation against experimental data is extremely difficult since any measured parameter will depend on the complete engine. Distribution of secondary gases and AFR (Air to Fuel ratio) are typical examples where traditional CFD methods fail. One proposed way to overcome these problems is to use 1D gas exchange models coupled with 3D CFD. The main problem with this approach is however the positioning and treatment of the boundaries between the models. Furthermore, the boundaries themselves will unconditionally cause disturbances in the pressure fields.

To elucidate the processes controlling the auto-ignition timing and overall combustion duration in homogeneous charge compression ignition (HCCI) engines, the distribution of the auto-ignition sites, in both space and time, was studied. The auto-ignition locations were investigated using optical diagnosis of HCCI combustion, based on laser induced fluorescence (LIF) measurements of formaldehyde in an optical engine with fully variable valve actuation. This engine was operated in two different modes of HCCI. In the first, auto-ignition temperatures were reached by heating the inlet air, while in the second, residual mass from the previous combustion cycle was trapped using a negative valve overlap. The fuel was introduced directly into the combustion chamber in both approaches. To complement these experiments, 3-D numerical modeling of the gas exchange and compression stroke events was done for both HCCI-generating approaches.

Numerical and modeling errors in computational aerodynamics consist of multiple components. Previous investigations at Volvo have shown that low Reynolds k-ε models generally give better levels in pressure over the rear base area of the car than the corresponding wall function based model. However, these computations were carried out on car shapes without wheels. This paper presents numerical simulations of the flow field around three versions of the Volvo validation car series (VRAK). The geometry is a typical car with flat floor and simplified tires. The three car models differ by their rear shape. The configurations are: one with a nearly flat base, a fastback with a sloping rear window, and a car with a roof wing. The influence of the near wall formulation of the standard k-ε model on drag and lift is investigated. The performance of the low Reynolds number version of the cubic k-ε model by Suga [7] is also investigated.

This paper describes results from fault injection experiments using heavy ions in the time-triggered communication protocol for safety critical distributed systems (TTP/C, C1 implementation). The observed results show that arbitrary faults in one erroneous node could cause inconsistencies in the cluster and thus jeopardize correctly working nodes and the whole communication system. The described inconsistencies resulted from either asymmetric value faults or slightly out of specification timing faults. This system behavior can be partly explained by too strict constraints on the fault handling algorithms using the membership agreement protocol.

In the continuous struggle to improve car body properties, and at the same time reduce the weight of the structure, new materials and body concepts are being evaluated. In competition with more self-evident lightweight materials such as aluminium and plastic composites, new and different grades of high-strength steels with various surface coatings are being introduced. From experience it is known that to be able to weld and join these steel grades under high-volume conditions, it is necessary to perform comprehensive testing to establish those assembly parameters which give a superior and reliable weld quality. To meet the demands of cost-effective low volume production, we can notice a tendency to move away from traditional uni-body concepts and into the direction of space-frame structures. These can preferably be manufactured out of high-strength steels by using production methods like roll-forming, hydro-forming and hot-forming.

Driver errors cause a majority of all car accidents. Forward collision avoidance systems aim at avoiding, or at least mitigating, host vehicle frontal collisions, of which rear-end collisions are one of the most common. This is done by either warning the driver or braking or steering away, respectively, where each action requires its own considerations and design. We here focus on forward collision by braking, and present a general method for calculating the risk for collision. A brake maneuver is activated to mitigate the accident when the probability of collision is one, taking all driver actions into considerations. We describe results from a simulation study using a large number of scenarios, created from extensive accident statistics. We also show some results from an implementation of a forward collision avoidance system in a Volvo V70. The system has been tested in real traffic, and in collision scenarios (with an inflatable car) showing promising results.

Today automotive system suppliers develop more-or-less independent systems, such as brake, power steering and suspension systems. In the future, car manufacturers like Volvo will build up vehicle control systems combining their own algorithms with algorithms provided by automotive system suppliers. Standardization of interfaces to actuators, sensors and functions is an important enabler for this vision and will have major consequences for functionality, prices and lead times, and thus affects both vehicle manufacturers and automotive suppliers. The investigation of the level of appropriate interfaces, as part of the European BRAKE project, is described here. Potential problems and consequences are discussed from both a technical and a business perspective. This paper provides a background on BRAKE and on the functional decomposition upon which the interface definitions are based. Finally, the interface definitions for brake system functionality are given.

The airflow around a detailed car underbody has been simulated using a commercial CFD software. Moving ground and rotating-wheel boundary conditions were applied in order to allow comparisons of Cd and dCd values with experimental data from a wind tunnel fitted with moving ground facilities. The calculated Cd and dCd figures compared very well with the available experimental results. Four configurations were tested and the maximum difference between experimental and numerical Cd values was 0.009. The individual contribution of different parts of the vehicle to the total drag was calculated and is discussed in this paper. This paper also describes in detail the numerical technique used to perform the computations.

The accuracy of computational fluid dynamics, CFD, has improved considerably over the years but still, large errors are present and vehicle parameters such as drag and lift are often poorly predicted. The current work is investigating how transient CFD would cope with a very complex flow structure around a surface mounted cube. A transient Reynolds averaged Navier Stokes model, RANS model, is presented together with a large eddy simulation model, LES model. Furthermore, two “industrial like” test cases have been simulated using a transient RANS model.

Numerical simulations of the flow inside a passenger compartment are compared with experimental data obtained from velocity field measurements using Particle Image Velocimetry (PIV). Comparisons are made in the front part of the passenger compartment with the air-distribution system operated in a ventilation mode. The sensitivty of the CFD-model to the boundary conditions was investigated and two different turbulence models were tested. Computations and experiments resulted in similar results for the overall flow field, however, rather large differences were found in the vertical spreading of the jet from the dashboard nozzle. The width of the jet was lower in the measurements than in the simulations. This difference is believed to be caused by the high diffusivity obtained when using a k-epsilon model in combination with an unstructured grid.